Repairing windows in Dubai since 2014
Gulf Extrusions Window and Sliding Door Repair in Dubai
We repair Gulf Extrusions windows and doors in Dubai, including Montana sliding systems and TB-600 hinged windows, as an official partner with genuine Gulf Extrusions parts. Adjustment with lubrication is 300 AED, a new handle 350 AED. The price is agreed before work begins, the warranty is 2 years, and a technician gets to you in about 30 minutes.
2014
Repairing since
2 years
Warranty on every job
24/7
Calls answered
Gulf Extrusions repairs we carry out
Nine jobs cover almost every Gulf Extrusions call-out in Dubai. Each is done with genuine Gulf Extrusions parts.
Montana, TB-600 or curtain wall: what fails and what it costs
Gulf Extrusions systems are built in different ways, so they break in different ways. Open the tab that matches yours to see the typical faults and prices.

Montana sliding and The Glide lift-and-slide systems
- Montana Thermal Break 120 mm
- The Glide
Montana is a heavy-duty thermal-break slider. Its panels run on single or double rollers, meet on an interlock and are pulled by flush handles. The Glide is a lift-and-slide system.
What usually goes wrong
- Panel scrapes along the trackSingle or double rollers under the panel worn outPrice at the door
- Flush handle no longer catchesLatch inside the recessed handle worn350 AED
- Light shows between two panelsInterlock EPDM gaskets worn flat50 AED / linear m

TB-600 and Hinged series windows and doors
- TB-600
- Hinged 42
- Hinged 45
TB-600 is a hinged thermal-break system with a 60 mm frame and EPDM gaskets. Installers also build it as a tilt-and-turn window. Hinged 42 and Hinged 45 have no thermal break.
What usually goes wrong
- Sash hangs on one cornerTilt-and-turn set worn, replaced as a kit2,500 AED / set
- Sash drops and rubs the sillHinges need resetting and lubrication300 AED
- Closed window lets air throughEPDM gasket has lost its spring50 AED / linear m

CW curtain wall systems
- CW 50
- CW 60
- CW 36
- Vortex 61.5
- Vortex 70
CW 50, CW 60, CW 36, Vortex 61.5 and Vortex 70 are the curtain wall lines in the Gulf Extrusions catalogue. On a facade the aluminium grid stays in place, and the work is on the glass and the gaskets that hold it.
What usually goes wrong
- Pane has crackedNew unit measured and made to size1,000 AED / m²
- Gasket has pulled back at the cornersOld gasket removed and a new one fitted50 AED / linear m
- Glazed frame sits looseFrame taken out and installed again550 AED / m²
Work out the price before we come
Prices from our fixed price list. The technician confirms them at the window before any work.
Gulf Extrusions repair price list
- Removal and Replacement of Wedge Gasket Seals50 AED / linear m
- Replacement of Aluminium Bottom Sealer350 AED
- Replacement of Double-Glazed Unit1,000 AED / m²
- Window Handle Replacement350 AED
- Multi-Point Lock700 AED
- Adjustment of the Mechanism and Lubrication300 AED
- Replacement of the Lock350 AED
- Tilt-and-Turn Hardware Set (PVC & Aluminium)2,500 AED / set
- Dismantling / Installation (Windows, Doors, Portals)550 AED / m²
Fixed prices, labour included. Montana rollers come single or double, so their price is confirmed at the door.
Gulf Extrusions repair in Dubai, in detail
Gulf Extrusions, also written GulfEx, is a Dubai aluminium extruder founded in 1976 and the flagship company of Al Ghurair Group. It runs its own plant in Dubai and publishes a long catalogue of window, door and curtain wall systems. The main lines:
- Montana Thermal Break 120 mm. A heavy-duty sliding system with a thermal break, for windows and doors. The panels run on single or double rollers, meet on an interlock and are moved by flush handles. A mosquito frame is part of the same system.
- TB-600. A hinged thermal-break system with a 60 mm frame, for windows and doors. Installers also build it as a tilt-and-turn window.
- The Glide. A lift-and-slide system.
- The Next. A thermal-break sliding system for windows and doors with concealed frames.
- Hinged 42 and Hinged 45. Hinged systems without a thermal break.
- TB 62, TB 105 and TB 900. Other thermal-break systems: TB 62 is hinged, TB 105 and TB 900 are sliding.
- CW 50, CW 60, CW 36, Vortex 61.5 and Vortex 70. Curtain wall.
Not sure your window is Gulf Extrusions? Send a photo of the track, the handle and the edge of the panel on WhatsApp, and the technician will tell by the profile.
One system slides and the other swings, so each has its own weak points.
Montana, sliding:
- Rollers. Single and double rollers are fixed under the panel with stainless steel screws. The screws last. The wheels and bearings do not: dust from the track grinds them until the panel scrapes. Rollers are priced at the door.
- Track. The running track is held in the frame by snap-on clips. Cleaning it and lubricating the rollers is part of adjustment at 300 AED.
- Interlock. Where two panels overlap, the interlock and its EPDM gasket keep dust out. When the gasket is worn flat, you can see light between the panels.
- Flush handles. The recessed handle also carries the latch. A worn one stops catching and is replaced for 350 AED.
- Frame corners. The corners are joined with cleats and sealed. If that seal opens, water finds its way into the frame. This is checked and priced on site.
TB-600, hinged:
- Hinges and tilt-and-turn gear. A dropped sash is usually cured by resetting the hinges. A worn tilt-and-turn mechanism is replaced as a set for 2,500 AED.
- EPDM gaskets. Summer heat takes the spring out of EPDM, and the closed window starts to let air through. New gasket costs 50 AED per metre.
Montana is built from few profiles: the same section goes around all four sides of the frame, and the same around the sash. The rollers, the track clips and the interlock are all made to those sections. A roller of another size raises or lowers the panel, the interlock stops overlapping as it should, and dust comes straight through the middle of the door.
The same goes for TB-600. Its EPDM gasket is shaped for the groove of the 60 mm frame, and a generic cord does not fill that groove.
As an official partner we fit genuine Gulf Extrusions parts, so the panel runs at the height the system was designed for and the window seals along its whole perimeter.
First the technician identifies the system: Montana, TB-600 or another Gulf Extrusions line. The parts differ, so this decides what is needed. Sliding panels are then checked on the track and hinged sashes on their hinges, and you hear a fixed price before work begins. Adjustment, lubrication, handles and gaskets are done on the first visit. Rollers and tilt-and-turn sets for the exact system are ordered and fitted on a second visit. Each repair has a 2-year warranty.
Related pages: aluminium window repair for hinged windows, sliding door repair for rollers and tracks, window hardware and lock repair for handles and mechanisms, window sealing for gaskets. Shops and offices are covered by commercial window repair. To book, use the contact page.
Our work on site
Our technicians at work
Portfolio
Articles
Practical guides on window and door repair in Dubai: foggy glazing, soundproofing, sliding doors, seals and more. Written by our repair team.
Tell Us Your Problem
Select your issue and get a free quote in under 2 minutes.
- Fast Response We call back within 5 minutes
- Free Estimate No hidden charges, transparent pricing
- 2-Year Warranty All repairs backed by warranty
Brands we repair
Official partner of every brand below, with access to their genuine parts in the UAE.
Aluminium14
uPVC4
Frequently Asked Questions
Still have questions?
Call or WhatsApp us: we take calls
24/7, emergency callouts around the clock.
-
Yes. We repair Montana sliding windows and doors, TB-600 hinged and tilt-and-turn windows and the other Gulf Extrusions lines anywhere in Dubai. We are an official partner with access to genuine Gulf Extrusions parts.
-
No. Both are Gulf Extrusions systems. Montana is the sliding line and TB-600 the hinged one. Their parts are different, so say which one you have when you call, or send a photo.
-
Track cleaning with adjustment and lubrication is 300 AED, a flush handle 350 AED, and new gaskets 50 AED per metre. Single and double rollers are priced at the door before the work.
-
We begin with adjustment and lubrication for 300 AED, which is often enough. If the mechanism itself is worn, a tilt-and-turn hardware set costs 2,500 AED.
-
In most cases, yes. Montana corners are joined with cleats and sealed, and that seal can open. The technician checks the joint on site and names the price there before starting.
Where We Work
Main Office
Pinnacle, Sheikh Zayed Road, Office 607, Al Barsha First, Dubai, UAE
Our offices in Dubai

